It appears that your cart is currently empty
TROMBONE HANDSLIDE MANDREL RACK
Keep handslide mandrels protected and in neat order with this sturdy wood rack. Constructed from ...
Keep handslide mandrels protected and in neat order with this sturdy wood rack. Constructed from solid oak, our nicely finished rack can be mounted either vertically against a wall, or positioned horizontally above or below a workbench. Holds 16 mandrels.DIMENSIONS: length: 24" (61cm) width: 6" (15.2cm) depth: 6" (15.2cm)
$46.50
Have you ever been straightening a badly bent slide pipe and - SNAP! - theslide buckles and must ...
Have you ever been straightening a badly bent slide pipe and - SNAP! - theslide buckles and must be replaced. Ronny's Safety Rod is a high density,thermoplastic rod that inserts into the slide before bending and greatly reducesthis risk. Two diameter sizes for inner and outer pipes, the 29" long rodsare strong enough to provide support but flexible enough to not restrictbending.
$12.00
Designed for aligning both inner and outer slidepipes, our #2076 Leveling Block is constructed us...
Designed for aligning both inner and outer slidepipes, our #2076 Leveling Block is constructed using heavy plate glass enclosedin a wood case. Two steel riser blocks machined perfectly flat set on either endof the glass. Slide pipes are set on the riser blocks to determine skew ortwist. Works great for soldering and reassemby work. Whensoldering, simply position the area receiving the heat off of either end of theblock. To help hold pipes in place when soldering order our #2078 TROMBONE SLID...
$189.50
TROMBONE SLIDE ASSEMBLY MAGNET
Our Trombone Slide Assembly Magnets are designed for securely holding slide pipes in position dur...
Our Trombone Slide Assembly Magnets are designed for securely holding slide pipes in position during reassembly and soldering.Precision machined from corrosion resistant, magnetic stainless steel and fitted with high strength, rare earth magnets.Work great with our #2076 TROMBONE LEVELING BLOCK or any slide assembly fixture that uses steel bars or plates to allow magnetic adhesion.Dimensions: Diameter: 1" (25.4mm) tapering to 0.42" (10.7mm) Length: 1-1/8" (28.5mm) Sold by each.
$18.00
Made from precision ground drill rod, each finely polished mandrel holds a diameter and roundness...
Made from precision ground drill rod, each finely polished mandrel holds a diameter and roundness tolerance of +/- 0.0005" (0.0127mm), qualities that far surpass other mandrels on the market.All mandrels have a full radius machined and polished on one end to prevent snagging while inserting into badly dented slide pipes and to prevent putting ridges in the crook area. The mandrel's other end is number indexed for easy identification. Overall mandrel length is approximately 36" (91cm).WHICH SI...
$535.50
Nylon brushes used for trombone handslide tubes. Sturdy galvanized wire with 1" (25.4mm) ring end...
Nylon brushes used for trombone handslide tubes. Sturdy galvanized wire with 1" (25.4mm) ring end #3512 Outer Slide Brush is vinyl coated to protect pipes Overall length: 32" (82cm) Double row, 4" ((10cm) brush part provides excellent scrubbing action
$6.98
TROMBONE HANDSLIDE CLEANING ROD
Thanks to repair technician Tony Hawks for hissuggestion to improve upon the flimsy, hard to hold...
Thanks to repair technician Tony Hawks for hissuggestion to improve upon the flimsy, hard to hold, cleaning and swabbing rodsused for trombone handslides.Ours has a sturdy shaft with a 5/16" (7.9mm) diameter and the 'T' handledesign offers excellent gripping and control compared to rods that have onlya ring on the end.Machined from stainless steel and brass, with an ABS handle, these rods arecompletely rust free and impervious to fumes and corrosives found in most shops.Extra large eyelet all...
$33.65
1 – 7 product(s) of 7