TOOLS

REPLACEMENT OUTER SHEATH - NEOPRENE

Outer neoprene rubber replacementsheath for: #6519 or #6519A Flexible Shaft Power Tool #6520 or #...

Outer neoprene rubber replacementsheath for: #6519 or #6519A Flexible Shaft Power Tool #6520 or #6520A Flexible Shaft Power Tool Any Foredom Series S, CC, R, SR, or L motors Caution: the neoprene sheath is moreflexible than the standard, and there is more risk of breaking the inner shaft from too tight a bend.

*DISCONTINUED BY MFR.*

HANDPIECE PIN & CHUCK WRENCH

For use with collet style handpiece.

For use with collet style handpiece.

REPLACEMENT MOTOR BRUSHES

Pair of motor brushes for our #6519Foredom Power Tool or #6520Foredom Power Tool(110 volt only)Al...

Pair of motor brushes for our #6519Foredom Power Tool or #6520Foredom Power Tool(110 volt only)Also work on any Foredom CC, DD, MM series motors (110 volt only)For 220 volt motors see #6521BMotor Brushes.

MAINTENANCE KIT

Maintenance kit for Foredom Power Tools.Includes: Replacement Inner Shaft Pair of motor brushes G...

Maintenance kit for Foredom Power Tools.Includes: Replacement Inner Shaft Pair of motor brushes Grease Operating Manual Works in any of the following: #6519 Flexible Shaft Power Tool #6520 Flexible Shaft Power Tool Any Foredom Series CC, DD, or MM motors (110 volts)

COLLET STYLE HANDPIECE

Handpiece constructed with pre-lubricated ball bearings that require no maintenance. Collet desig...

Handpiece constructed with pre-lubricated ball bearings that require no maintenance. Collet design works best for using cutting burs, wheels and buffs.Comes with wrench and 3 different size collets for holding the following shaftsizes:3/32" (2.38mm)......1/8" (3.17mm) ......1/4" (6.35mm)Handpiece overalllength: 5.6" (14.2cm)Handpiece diameter: 1.0" (25.4mm)Handpiece weight: 5.9 oz (167 g)Easily attaches with quick disconnect to any Foredom Flexible Shaft Power Tool.

MAGNETIC DENT REMOVAL MUSHROOM - 1.625" (41.3mm)

Designed for use with magnetic dent removal tools,these discs attach to the end of the magnet to ...

Designed for use with magnetic dent removal tools,these discs attach to the end of the magnet to provide a radiused surface.Precision machined steel.Diameter: 1.625" (41.3mm)

PRECISION RULE - 1/64", 1/32"

Precision stainless steel rule. Includes pocket clip thatfunctions as depth or height gauge. Back...

Precision stainless steel rule. Includes pocket clip thatfunctions as depth or height gauge. Back side lists fractional to decimal equivalents.SPECIFICATIONS: length: 6" (150mm) width: 15/32" (12mm) graduation: edge A: 1/32" edge B: 1/64"

*DISCONTINUED*

PILOT BUSHING - CENTER TENON - VITO

Designed to work on Vito Bb soprano plastic clarinet upper joints when counterboring for center t...

Designed to work on Vito Bb soprano plastic clarinet upper joints when counterboring for center tenon replacement.Machined from high density plastic with 3/16" (4.76mm) diameter pilot hole.Outside diameter: 0.584" (14.8mm). TenonReplacement Helpful Tips TenonReplacement Tooling

BEARING MODULE RETAINING NUT (REPLACEMENT)

Replacement retaining nut for #2251N Bearing Module

Replacement retaining nut for #2251N Bearing Module

*DISCONTINUED*

VOTAW DISC SANDER

Our #2391 Disc Sander is designed to trim and square up the ends of key hinges, hinge rods (long ...

Our #2391 Disc Sander is designed to trim and square up the ends of key hinges, hinge rods (long screws), slide pipes, brass tube, etc. Designed for fast setup, simply clamp bottom recessed area of chassis into standard bench vise and sander is ready to use.For hinge rods and tubing, use any of the four different sized 'V' slots located on the carriage top. To accommodate various key shapes, position one or both key saddles into the desired carriage holes to support the key hinge. Bring end t...

*DISCONTINUED*

PUNCH & THREAD CUTTING TOOL

Our Punch and Thread Cutting Tool is an excellentaddition to any woodwind bench. Precision design...

Our Punch and Thread Cutting Tool is an excellentaddition to any woodwind bench. Precision designed and constructed to perform the followingtasks: key pin removal and installation thread cutting hinge rods flattening ends of needle springs Comes complete with: Main tool frame Drill chuck - open bore - capacity 0.015" - 0.25" (0.4mm - 6.5mm) 3 Key pin punches 3 Key hinge bases - 2 'V' blocks and 1 lead block Hammer punch & Anvil base - tool steel for ...

*DISCONTINUED*

BELL RIM BLOCK - SMALL

Our thanks to technician Mike Webb for coming up with this great idea for help in straightening b...

Our thanks to technician Mike Webb for coming up with this great idea for help in straightening bell rims.Machined from 2" (51mm) thick UHMW plastic, these blocks provide a solid, flat surface for straightening alto saxophone and other small bells. Cut-out area in side allows for narrow, focused work range as well as clearance for alto saxophone bell key levers.Clamps in any standard bench vise.Diameter: 6" (152mm).For other larger bells we offer #2388 BELL RIM BLOCK - LARGE.

*DISCONTINUED*

LOMAX MOUTHPIECE MEASURING KIT

From repair shop technicians and mouthpiece manufacturers to professional players and educators, ...

From repair shop technicians and mouthpiece manufacturers to professional players and educators, the Lomax Mouthpiece Measuring Kit is a 'must have' item for anyone interested in making quick, accurate measurements of woodwind mouthpiece tip openings, as well as determine facing specifications. Built in collaboration with woodwind mouthpiece maker Michael Lomax, upon whose initial concept the tool is designed, we are confident this kit will soon become a standard in the industry. TIP OPENIN...